GROOMING 


Curvations - Follow the Curve for a Silky Smooth Shave (model #LWD500CS)

Curvations ladies' shaver banner

Infiniti by Conair™ revolutionizes women's shaving by following the curves! Only Curvations has a 360° swivel head that automatically adjusts to all the subtle contours of a woman's body.



Before Shaving

Shaving Your Legs/Bikini Area

Shaving Your Underarms

How to Clean Your Shaver



BEFORE SHAVING

1. Before wet shaving, you may wish to prepare your legs and underarms with shaving cream or soap. If a soapy lather is applied to the skin, the shaver will glide smoothly over the skin and clean away oil residue while at the same time removing hair. Caution: DO NOT use shaving gels, as these products can clog your shaver foils.

2. When dry shaving, be certain that your skin is clean. If you have sensitive skin, you may want to apply talcum powder before and after you shave.

3. Clean your shaver after each use. This will ensure the best performance. (Please refer to How to Clean Your Shaver section for further instructions.)

4. Although the shaver is washable, do not immerse in water for extended periods of time.



Exclusive 360° Swivel

Your new Infiniti by Conair women's razor features an exclusive Conair 360° swiveling head. It will automatically adjust to your different body contours for the ultimate silky smooth shave. A locking switch on the back of the trimmer allows you to position the head in a stable, nonswiveling mode. You should select the desired mode before following the Instructions for Use section.



INSTRUCTIONS FOR USE

1. Remove the plastic blade guard.

2. Slide the main switch up to the on position.

3. After each shave, switch the unit off, clean, and replace the blade guard.

4. Put the unit back on the charging stand for storage and/or recharging.



SHAVING YOUR LEGS/BIKINI AREA

NOTE: Pushing the shaver against the skin too hard will prevent the hairs from entering the foils to be cut. Experience will show just the right pressure to use to maximize performance.

1. Prepare your legs for wet or dry shaving.

2. Turn shaver on.

3. Shave with smooth, steady strokes up and down your leg.

4. Keep the full shaving head in contact with your skin.

5. For best results, shave against the direction of hair growth.

6. Your shaver has an integral cutter feature which is ideal for shaving longer hairs. The shaver also has a bikini pop-up trimmer for your complete shaving needs. To use pop-up trimmer, push button upward with thumb. For best results, use the bikini pop-up trimmer for really long hairs.

7. When you finish shaving, turn the shaver off. Important: After several uses, you will be able to determine the optimum shaving method for your legs and bikini area.



SHAVING YOUR UNDERARMS

1. Prepare your underarms for wet or dry shaving. (Be sure that your skin is clean.)

2. Turn the shaver on.

3. Lift your arm until the skin under the arm stretches slightly.

4. Use the trimmer first to cut any long hair, stroking trimmer against the direction of hair growth.

5. Hold the shaver so that it is in full contact with your skin, and shave with gentle strokes.

6. It is important to press lightly. Pressing too hard may lead to skin irritation.

7. When finished shaving, turn the shaver off. Important: After several uses, you will be able to determine the optimum shaving method for your underarms.



HOW TO CLEAN YOUR SHAVER



DETACH SHAVER HEAD AND FOIL FRAME

1. Make sure the unit is in the off position before detaching the shaver head.

2. Hold the shaver body and press the release buttons on both sides of the shaver head, then remove the shaver head by pulling it straight up from the body.

3. Gently press the foil frame release buttons on both sides of the shaver head and lift the foil frame straight up from shaver head. The cutter will now be in view; be careful not to push on the foils as they are delicate and can be easily damaged.



RINSE THE SHAVER HEAD

1. Rinse the shaver cutter and foil frame under warm or cold running water only; do not use hot water (you can also use the cleaning brush, which is included).

2. Allow the shaver head and foil frame and cutters to air-dry before replacing foil frame.



CAUTION

1. When shaking off excess water, hold the main unit firmly to prevent releasing the head assembly or dropping the unit.

2. Do not use a dryer or heater to dry the shaver. This may result in malfunction or damage to the shaver.


NOTE: Never pull on the charging stand cord. Never twist or wrap the cord around the charging stand. Lay it flat in the storage pouch provided with the cord coiled up when not in use.



REPLACE SHAVER HEAD


Once the shaving head is dry, hold and press the shaver head release buttons and reattach to the shaver body.


Note: if the body of the shaver becomes dirty, wipe off with a damp cloth and mild detergent or soap. Never use thinner, other solvents, or any harsh cleaners.



REPLACING THE FOILS FRAME

1. It is time to replace the foils when you find you have to push harder on the shaver to get a close shave, or when you have to go over your leg area more often to get a smooth result, or when you experience skin irritation. Replacement time will depend on how often you use your shaver and how quickly your hair grows.

2. When replacing the foils, press the foil frame release buttons on both sides of the shaver head, remove and then gently insert the new foil frame into position, being careful not to push on the foils.



REPLACE THE CUTTER (INNER BLADES)


CAUTION: NEVER REPLACE THE CUTTERS WITHOUT REPLACING THE FOILS AS WELL.

1. Press the release buttons on both sides of the shaver head, then remove the shaver head by pulling it straight up from the body; gently remove the foil frame.

2. Hold both sides of the inner blades and pull straight up.

3. Firmly hold the new inner blade and gently guide it into the inner blade mount.


Caution: MAKE SURE YOU DO NOT LOSE THE SMALL SPRING UNDER THE CUTTERS.

4. Firmly press the inner blades until they snap into place.

5. Replace the foil frame.



POP-UP TRIMMER ASSEMBLY


NOTE: WE DO NOT RECOMMEND REPLACING THE TRIMMER ASSEMBLY YOURSELF. THIS REQUIRES A SPECIAL TOOL FOR REPLACEMENT. TAKE OR SEND THE SHAVER TO A CONAIR SERVICE CENTER FOR SERVICE.
 
 
 
TIPS & TECHNIQUES
STYLING TIPS
[GROOMING]
GARMENT CARE
HEALTH & WELLNESS
HOME CARE
ORAL CARE
Email Signup
  •  
  •  
  •  
Select the topics you would like to receive emails about:
Unsubscribe
Please enter your email address:  
Unsubscribe - before you go
, you can narrow down your options and we will ONLY send you emails that pertain to that particular category.
You have been unsubscribed
We're sorry to see you leave. Goodbye!
Your lists have been changed
Here is a confirmation of the list you have subscribed to: