Enjoy Free Shipping on All Orders Over $100!
Quick User Guides
Select the type of scale you own
Before Using Scale
- Remove all packaging materials.
- Remove the isolator tab from the battery compartment – without opening the battery cover at the bottom of the scale, gently pull out the isolator tab. (If the tab cannot be pulled out or if the display does not light up after the tab is pulled, remove the screw from the battery cover and remove the cover. Gently pull out the isolator tab. Ensure the batteries are installed correctly. Replace the battery cover and tighten the screw.)
- For best accuracy, place scale on tile or hardwood floor, rather than on uneven, flexible or soft flooring (such as carpet).
- Set switch on the bottom of the scale for measuring in pounds (lb.) or kilograms (kg).
To Measure Weight
(Instant-On Scale) - Step onto the scale and stand still. You will see the display flash “000” for a few seconds before your weight displays
- Once you step off the scale, the scale will turn off automatically.
- Note:
1. If the scale is overloaded, “Err” will appear. - Lo” will appear if batteries are low and need to be replaced.
To Measure Weight
(Tap-On Scale) - Quickly and firmly tap center of the scale with foot to turn it on.The display lights up.
- Wait until “0.0” appears.
- Step onto the scale and stand still. You will see the display “000” flash for a few seconds before your weight displays
- Once you step off the scale, the scale will turn off automatically.
Note:
If you step on the scale before “0.0” appears, the scale will not function properly. “Err” will appear.
If the scale is overloaded “Err” will appear.
If you step on the scale before “0.0” appears, the scale will not function properly. “Err” will appear.
If the scale is overloaded “Err” will appear.
Before Using Scale
- Remove all packaging materials.
- Remove the isolator tab from the battery compartment – without opening the battery cover at the bottom of the scale, gently pull out the isolator tab. (If the tab cannot be pulled out or if the display does not light up after the tab is pulled, remove the screw from the battery cover and remove the cover. Gently pull out the isolator tab. Ensure the batteries are installed correctly. Replace the battery cover and tighten the screw.)
- For best accuracy, place scale on tile or hardwood floor, rather than on uneven, flexible or soft flooring (such as carpet).
- Set switch on the bottom of the scale for measuring in pounds (lb.) or kilograms (kg).
Using the Weight-Only Mode
Instructions for customizing your WW Body Analysis Scale are below. However, the scale does not need to be programmed to operate as a simple weight-only scale.
- Step on the scale and stand still to measure your weight.
- The weight reading stays lit for several seconds. Then the scale will shut off automatically.
Customizing Your Body Analysis Monitor
This scale can be customized for up to 4 users. While the customization process is not difficult, it may be easiest to read all the instructions first to familiarize yourself with them. Then keep the instruction manual handy as you go through the process step by step.
Note: This is a general guide for Body Analysis Scales, operation of your particular scale may vary, consult the user manual for best results.
- To set your user data
Press on the scale with one of your feet and take off your foot once it turns on before a weight reading appears, and wait until “0.0” appears. - Setting the user number
Press the SET button. The number “P-01” will appear and blink. Use the Up/Down arrows to select a user number (P-01 to P-04). Press SET to confirm. - Setting the height
Next, the inch symbol or CM lights up (if switch is set to LB default, height is in inches; if switch is set to KG, the CM lights up). Press the up or down arrows to adjust the height. Pressing and holding either the up or the down arrow will advance numbers quickly. Press SET to accept the height. Scale enters the age setting mode - Setting the age
AGE appears and the default age 25 flashes. Press the up or down arrows to adjust the age and press SET to confirm. The scale enters the gender setting mode. - Setting the gender
A gender icon flashes. Press the up or down arrows to choose between male and female gender. - Displaying and storing data
Once gender is set, data storage is complete. Scale will display your stored data: User number, Height and Age will each show for a few seconds. - The scale will display “0.0.” Then you could press the SET button to set (revise) the user data again, or set user data for other users; you could also step on the scale to do a body analysis directly (see the following instructions about body analysis).
Buttons: USER, SET, Up and Down arrows
Body Analysis
- Operate the scale on a secure, flat floor. Press on the scale with one of your feet and take off your foot once it turns on before a weight reading appears, and wait until “0.0” appears. Press the USER button repeatedly until your user number shows on the display.
- Stored data for your user number appears (User number, Height and Age) then the scale displays “0.0.”
- Step on the scale barefoot with your feet aligned on the electrodes (metal strips) on both sides of platform. NOTE: You must be barefoot in order for the scale to read your body analysis measurements.
- Your current weight will be displayed for a few seconds.
- Next, the display will show your body fat weight
- Then the display will show your body fat percentage.
- Next, the display shows your body water percentage.
- Then, the display shows your bone mass value.
- Next, the display shows your Body Mass Index (BMI) score.
- Then LCD will display CURRENT WEIGHT, FAT WEIGHT, BODY FAT, BODY WATER, BONE MASS, and BMI again, and then will turn off automatically.
Before Using Scale
Precautions for Use
CAUTION! Use of this device by persons with any electrical implant such as a heart pacemaker, or by pregnant women, is not recommended.
CAUTION! Use of this device by persons with any electrical implant such as a heart pacemaker, or by pregnant women, is not recommended.
- Remove all packaging materials.
- Remove the isolator tab from the battery compartment – without opening the battery cover at the bottom of the scale, gently pull out the isolator tab. (In case the tab cannot be pulled out, or if the scale display does not work after you have pulled the isolator tab, remove the screw from the battery cover and remove the cover. Gently pull out the isolator tab or any pieces of it that may block the battery contacts. Ensure the batteries are installed correctly. Replace the battery cover and tighten the screw again.)
- For best accuracy, place scale on tile or hardwood floor, rather than uneven, flexible or soft flooring (such as carpet).
Download the WW Scales by Conair scale app.
You can download the app from the App Store or Google Play.
Download the app or search “WW Scale”
Download the app or search “WW Scale”
Set-Up
Once you download the app, open it and be prepared to register following the on-screen prompts. You will need your scale near you and activated to record your details. It is necessary to complete your profile set-up for your scale to track your measurements and create graphs and charts.
- First step, select your unit of measurement on your scale – either pounds (lb) or kilograms (kg). You can easily make your selection by depressing the tab (button) on the underneath of your scale. (This will wake your scale up, so no need to tap to turn on)
- Open the WW Scale app on your mobile device. Be sure the Bluetooth setting is turned on (go to your smart phone’s settings and check if Bluetooth is turned on).
- Your app will welcome you! And it will then allow you to connect your scale to your mobile device. Once connected you can select your user number.
On the first screen of the WW Scale app you will see 2 buttons on the bottom for log in and Register. If you already have a WW Account, choose log in. Otherwise, choose register if you don’t yet have a WW account.
When registering for the first time, fill in the information requested to complete the registration process.
IMPORTANT: You will see a screen that asks for permission to share your weight data with the App. You must agree to this in order for the Scale to transmit your weight information to the App. Press OK to proceed once you have read and agree to this permission request.
Note: If you are using the same smart phone for multiple users of the same scale, each user is required to Log In, and Log out before and after use. If a user does not log out after using the scale, the next time the smart phone is used, it will remain on the user who was last logged in. If you are using separate smartphones, there is no need to log out after each use.
Transmitting data
After your device and scale have been paired, you can transmit data to the device via Bluetooth. You will see a Bluetooth icon and a check mark on your screen which indicates that you’re connected. Step on scale with bare feet. Stand still to see your weight. The scale will display your weight first, and a few seconds later, your body analysis data will be read and displayed.
For use of your scale without using the app
Please consult the instruction booklet that was included with your scale. Or Download it now.